您好,歡迎光臨萊州聚峰機械有限公司官方網站!

服務熱線

400-879-1999

你所在位置: 首頁 >> 新聞資訊 > 行業資訊 >
行業資訊

全自動攪拌車離合器掛檔不好怎么找原因?

來源:http://www.bangping.net/ 時間:2022-04-22

  攪拌車車主在駕駛期間時常會遇到問題,比如說離合器踏板已踩到底,但掛擋很困難,勉強掛上擋后,尚未放松離合器踏板,全自動攪拌車已行駛或熄火。那么全自動攪拌車離合器掛檔不好怎么找原因?
  Mixer car owners often encounter problems during driving, such as the clutch pedal has been stepped to the bottom, but it is difficult to hang up the gear, barely hanging up the clutch pedal, the automatic mixer has been running or flameout. So how to find the reason why the clutch of automatic mixer is not good?
  將離合器底蓋拆下,把變速器掛入空擋,離合器踩到底。然后,用起工具撥動從動盤。如能輕松撥轉,說明離合器分離良好;如撥不動,說明離合器分離不徹底。并檢查全自動攪拌車離合器踏板自由行程是否過大,并調整。
  Remove the clutch bottom cover, put the transmission into neutral, and press the clutch to the bottom. Then, use the pick tool to turn the slave plate. If you can easily turn, that the clutch separation is good; If not, the clutch separation is not complete. And check the automatic mixer clutch pedal free travel is too large, and adjust.
  檢查全自動攪拌車分離杠桿高度是否一致、是否過低。在車下撥動分離撥叉,使全自動攪拌車分離軸承前端靠在分離杠桿內端面上,轉動離合器一周進行查看,如果分離杠桿的內端能同時和分離軸承接觸不上,說明分離杠桿的高度不一致,需應進行調整。
  Check whether the height of separation lever of automatic mixer is consistent and too low. Under the car dial the separation fork, so that the front end of the automatic mixing truck separation bearing is on the inner end of the separation lever, turn the clutch for a week to check, if the inner end of the separation lever can not contact with the separation bearing at the same time, the height of the separation lever is inconsistent, and it should be adjusted.
  如果分離杠桿高度一致,仍然分離不徹底,就要檢查杠桿高度。將各分離杠桿調到同樣的高度,如果能徹底分離,說明原來調整不當或是磨損過甚。分離杠桿調整之后,須重新調整離合器踏板的自由行程。
  If the separation lever height is consistent and the separation is still incomplete, check the lever height. The separation lever is adjusted to the same height, if it can be completely separated, the original adjustment is improper or wear too much. After the separation lever adjustment, the free travel of the clutch pedal must be readjured.
  如果上述調整正常后,仍然分離不徹底,就要拆下全自動攪拌車離合器,檢查從動盤是否裝反、軸向移動是否困難、主從動盤有無翹曲、分離杠桿螺釘是否松動、浮動銷是否脫落。
  If the above adjustment is normal, the separation is still not complete, it is necessary to remove the automatic mixing car clutch, check whether the driven plate is installed, whether it is difficult to move in the axial direction, whether the main and slave moving plate is warping, whether the separation lever screw is loose, whether the floating pin falls off.
  對于全自動攪拌車的離合器,除上述檢查外,還應檢查制動液是否缺少,管道是否滲漏并排出液壓系統內的空氣。更多內容的了解您可以來網站www.bangping.net看看相關資訊!
  For the clutch of automatic mixer, in addition to the above inspection, should also check whether the brake fluid is missing, whether the pipeline leakage and discharge of air in the hydraulic system. For more information, you can come to www.bangping.net!
上一篇:混凝土攪拌車的干燥罐什么時候更換?
下一篇:混凝土攪拌車的溫度如何進行有效管理?
tag:混凝土攪拌車,小型混凝土攪拌車,全自動混凝土攪拌車
當前位置: 首頁 - 新聞資訊 > 行業資訊 >

全自動攪拌車離合器掛檔不好怎么找原因?

作者:中科聚峰混凝土攪拌車廠家 時間:2022-04-22

  攪拌車車主在駕駛期間時常會遇到問題,比如說離合器踏板已踩到底,但掛擋很困難,勉強掛上擋后,尚未放松離合器踏板,全自動攪拌車已行駛或熄火。那么全自動攪拌車離合器掛檔不好怎么找原因?
  Mixer car owners often encounter problems during driving, such as the clutch pedal has been stepped to the bottom, but it is difficult to hang up the gear, barely hanging up the clutch pedal, the automatic mixer has been running or flameout. So how to find the reason why the clutch of automatic mixer is not good?
  將離合器底蓋拆下,把變速器掛入空擋,離合器踩到底。然后,用起工具撥動從動盤。如能輕松撥轉,說明離合器分離良好;如撥不動,說明離合器分離不徹底。并檢查全自動攪拌車離合器踏板自由行程是否過大,并調整。
  Remove the clutch bottom cover, put the transmission into neutral, and press the clutch to the bottom. Then, use the pick tool to turn the slave plate. If you can easily turn, that the clutch separation is good; If not, the clutch separation is not complete. And check the automatic mixer clutch pedal free travel is too large, and adjust.
  檢查全自動攪拌車分離杠桿高度是否一致、是否過低。在車下撥動分離撥叉,使全自動攪拌車分離軸承前端靠在分離杠桿內端面上,轉動離合器一周進行查看,如果分離杠桿的內端能同時和分離軸承接觸不上,說明分離杠桿的高度不一致,需應進行調整。
  Check whether the height of separation lever of automatic mixer is consistent and too low. Under the car dial the separation fork, so that the front end of the automatic mixing truck separation bearing is on the inner end of the separation lever, turn the clutch for a week to check, if the inner end of the separation lever can not contact with the separation bearing at the same time, the height of the separation lever is inconsistent, and it should be adjusted.
  如果分離杠桿高度一致,仍然分離不徹底,就要檢查杠桿高度。將各分離杠桿調到同樣的高度,如果能徹底分離,說明原來調整不當或是磨損過甚。分離杠桿調整之后,須重新調整離合器踏板的自由行程。
  If the separation lever height is consistent and the separation is still incomplete, check the lever height. The separation lever is adjusted to the same height, if it can be completely separated, the original adjustment is improper or wear too much. After the separation lever adjustment, the free travel of the clutch pedal must be readjured.
  如果上述調整正常后,仍然分離不徹底,就要拆下全自動攪拌車離合器,檢查從動盤是否裝反、軸向移動是否困難、主從動盤有無翹曲、分離杠桿螺釘是否松動、浮動銷是否脫落。
  If the above adjustment is normal, the separation is still not complete, it is necessary to remove the automatic mixing car clutch, check whether the driven plate is installed, whether it is difficult to move in the axial direction, whether the main and slave moving plate is warping, whether the separation lever screw is loose, whether the floating pin falls off.
  對于全自動攪拌車的離合器,除上述檢查外,還應檢查制動液是否缺少,管道是否滲漏并排出液壓系統內的空氣。更多內容的了解您可以來網站www.bangping.net看看相關資訊!
  For the clutch of automatic mixer, in addition to the above inspection, should also check whether the brake fluid is missing, whether the pipeline leakage and discharge of air in the hydraulic system. For more information, you can come to www.bangping.net!

截屏,微信識別二維碼

最刺激黄a大片免费观看下载_2021最新国产精品网站_日本乱码中文在线观看_免费的日本中文字幕视频